This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

The unit should be isolated from the electricity supply before removal of any covers. Great care must be employed when working with high pressure carbon dioxide, and in no cases should the maximum operating pressure of 0.4MPa (4 bar) be exceeded.

• The appliance is not suitable for installation in an area where a water jet could be used.
• The appliance has to be placed in a horizontal position.

WARNING: Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction.
WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

This appliance is intended to be used in household and similar applications such as:-

• Staff kitchen areas in shops, offices and other working environments
• Farm houses and by clients in hotels, motels and other residential type environments
• Bed and breakfast type environments
• Catering and similar non-retail applications

A-weighted emission sound pressure level is below 70 dB(A)

• Always place the dispenser in its vertical position, on a surface which can capably support its weight.
• During use this machine must remain in its upright position.
• Adequate ventilation must be allowed for.
• Keep the machine away from sunlight, heat and moisture.
• Power and water supply points must be available near the dispenser, and must meet the criteria specified in the ‘Specification’ section of this manual.
• The environment where this machine is installed must be free of dust and corrosive/explosive gases.
• Clean the lens every 2 weeks minimum using screen cleaner – ensure unit is off during cleaning.

Contents:
1 no B6 Unit
1 no 2.0m Power Cord Set

1 no Co2 Regulator with Gauge & Connection tube*
1 no Warranty Card

The product is supplied from the factory in clean condition, but we recommend that a sanitisation procedure is caried out at the point of installation, according to the sanitisation instruction relevant to this model, which can be found in the respective Instruction & Operation Manual

NOTE: Failure to use sanitising products and processes approved by Borg & Overström will invalidate your warranty.

This operation must only be carried out by trained staff. 

A sanitisation procedure is recommended every 6 months.

Turn off incoming mains water

Briefly press chilled dispense button to release internal water pressure from the machine.

Remove the existing filter

Use hand gel and put on protective gloves.

Add 25 ml of Bioguard Internal Sanitising Solution to a clean and empty service filter cartridge.

Connect to filter head.

Turn on incoming water, allow the service filter cartridge to fill

Dispense water using the chilled button until the water appears pink. Repeat with sparkling & ambient water buttons.

Leave the solution inside machine for sanitisation to take effect (minimum 5 minutes) while thoroughly cleaning the dispenser externally. (All maintenance operations must be carried out with the dispenser switched off.)

Pay particular attention to the dispense faucet and the push button controls. For this use Sterizen External Sanitiser and Sanitising Wipes. 

Remember to include the drip tray. If a Waste Overflow System is fitted, empty this and flush through with a small amount of sanitisation fluid if needed.

Attend to any cosmetic marks as needed. For this we recommend the use of Bioguard External Sanitiser. 

Reconnect the power and switch on the dispenser.

When the external cleaning (minimum 5 minutes) is completed, flush the machine using the chilled button with clean water until the dispense water runs clear. Repeat briefly with the ambient and sparkling buttons if present.

Turn off water and briefly press chilled dispense button to release internal water pressure from the machine.

Remove the service filter. Retain service filter for reuse.

Fit new filter and turn on incoming water supply.

Pre-flush the new filter to waste using the chilled button until the water appears clear and is free of air. Flush through a small amount of water to check all functions.